1. Place the red clip and clamp the battery positive (+).
2. Clamp the battery negative (-) with the black clip.
3. Start your car.
4. Start, you can remove the red, black clip.
1. Charger plugged into the RCA charging hole to charge, charge to full green light is lit, that is to complete the charge .Charging time should not exceed 24 hours.
2. When the unit is not used for two months, please recharge.
3. Full charge at any time, can make the machine longer life (a long time without charging will cause WP128 battery damage).
- Output operation:
1.WP128 front RCA output hole, you can use 50W of the output.
2.WP128 positive USB output hole, you can use 5V2A 3C products for charging use.
3.WP128 cigarette lighter behind the mother seat, can be connected to various types of vehicle equipment can output 10A.
- Weight: 5 kgCharging voltage:
- AC 100-240 voltsBattery
- Specifications: Sealed Battery – DC 12V 14 amps
- Contents: host 1, 12V1.6A charger 1, car charger line 1
- Switchable DC12V & DC24V
- Built-In 2pcs of DC12V 17A sealed rechargeable lead-Acid batteries.
- 10A fuse protection
- Output from clamp : Depend on 12V/24V switch position.
- Output from socket : DC 12V Only.
- Capacity testing : turn the switch to DC12V.
- Charge method : turn the switch to DC12V. When charge with adaptor & cigarette plug.
- This 12 Volt automotive power supply is used to avoid the loss of memory during the battery replacement.
- Power supply : 12V battery (recommended) or 9V battery.
- Function : LED display, mis-connected Protection, low battery capacity alarm.
- Applicable : Vehicle equipped with OBD II connector.
- All the tool you need to work with spring locking coupling, fuel line, and tranmission cooler line.
- Contents :Spring locking tool : 3/8″ (Red), 1/2″(Blue), 5/8″(Black), 3/4″(White)Fuel
- To fix A/C compressor crankshaft pulley and be convenient to install & remove centre screws
- Adjusting three-stud design for GM R-4 compressors, also has applications on some GM, Warne, Pitts and Ogura clutches
- Size of three stud : 3.6, 8.0mm
- All the disconnect tool, you need to work with spring locking coupling, fuel line and transmission cooler lines.
- Contents : Aluminium disconnect tool : 1/4″ (Black), 5/16″ (Red), 3/8″(yellow),(Blue). Two ends disconnect tool : 5/16″ – 3/8″ Long disconnect
- These tools are designed to remove the clutch hub of compressor
- There are 2 models of 4 clutch hub remover in this tool kit
- Some removers also can install the clutch hub
- Avoid winter freeze-ups and summer boil-over.
- Test all permanent (Ethylene Glycol) solutions with radiator hot or cold.
- Two scale show freeze point of radiator solution and boiling point of summer coolant.
- The Max Display Valve : 3200counts, Accuracy rating ±0.5%.
- R.P.M : 600~3200/6000~12000 rpm.
- Dwell Angle : 4, 5, 6, 8, Cyl.
- Working Duty% : 0~90°C/-22~1400°F.
- AC/DCV : 0~600V.
- Electric Current : 0~10A.
- Electric Resistance : 320~30 MΩ.
- Frequency : 10~32 KHZ.
- Temperature : -30~750.
- Finally know when you need to replace your brake fluid.
- Moisture is the enemy of your brake system as brake fluid absorbs moisture.
- Takes the guessing game out of determining how much moisture is in the system.
- Inexpensive tool for checking the brake fluid in all your vehicle.
- Determines if the fluid needs to be changed or not.
- 3 LEDs make it easy and takes only seconds.
● Laser ON/OFF ; ⁰C/⁰F Selection
● Changeable between ℃ and ℉
● Resolution: 0.1℃ (0.1℉)
● Accuracy : ±2⁰C / ±2%
● Distance Sport Ratio : 12:1
● Emssivity : 0.95 (Pre-Set)
● Response time & Wavelength : 500ms & (8-14um)
● Infrared Thermometer : -32⁰C ~ 360⁰C
● Auto Poer Shut Off
● AAA x2 Battery Operation